FloorBuffers.com brings you a great selection of floor buffers at prices that fit almost any budget. If you happen to find the same item at a lower price, contact us before you buy.
Only orders shipped to Illinois, Iowa, Michigan, Minnesota, and Wisconsin are charged sales tax
|
15 inch Explosion Proof Floor Buffer
 |
|
| |
15 inch Unico Explosion Proof Floor Buffer
· Bassine Scrub Brush Included
· For Hard Floor Use Only
· 1.0 HP Motor
· 1 Year Power Train Warranty
Regular Price: $6450.00
Sale Price: $5860.00
This 15 inch explosion proof floor machine comes with a bassine medium duty scrubbing brush and is classified for use in Class 1
Hazardous Locations, as described by the National
Electrical Code (NEC). The Unico explosion proof floor buffers are tested
with respect to the acceptability of operation in the presence of flammable
and explosive mixture of specific vapors and gases with air. Equipment classified
for use in Class 1 locations is not necessarily acceptable for Class 2 locations
as it may not be dust-tight or operate at a safe temperature when blanketed
with dust. This machine is available in 50 or 60 hertz, and 110 or 220 volts. If you are not in need of an explosion proof floor buffer, please take a look at our complete line of 15 inch rotary floor buffing machines.
Protection against explosions in hazardous locations requires that all electrical
equipment exposed to the flammable or combustible atmospheres be of a type suitable
for installation in such locations. Equipment should be installed in circuits
with overload and short-circuit protection for established ratings.
For explosion proof equipment as defined in the NEC, acceptability of use in
hazardous locations will be endangered should openings or other alterations
be made in the enclosure. Holding bolts of enclosing cases and threaded parts
must be screwed tight. Continued acceptability of installation will depend upon
proper maintenance.
Warnings: - Important to read before
use!
· Use ONLY static conductive and spark proof accessories that
are certified for use in hazardous locations. These machines and accessories
are designed to comply with the NEC.
· All electrical equipment must be installed and used in strict accordance with
the NEC.
· Regular maintenance inspections are a must! The electrical cord must be inspected
every time the machine is used. Any cuts or cracks in the insulation on the
cord must be replaced before using.
- Motor: 1 H.P. motor, U.L. listed (Class 1, Group D), ventilated, ball-bearing
for operation on 60 Cycle Phase, 115 / 230 Volt current, suitable for operation
in hazardous locations. Brush speed is 175 R.P.M. through gear reduction.
- Brush: Explosion proof brushes have an aluminum block and have bronze wire throughout
the fill to make them conductive. Pad holders and non-approved
brushes will void the explosion proof capabilities
of this machine. All brushes must be approved by the factory.
- Gear Unit: Completely enclosed and sealed planetary type gear reduction unit. Triple
planetary gears assure long life and quiet operation. The unit is lubricated
at the factory and requires no further attention.
- Housing: Heavy duty, reinforced cast aluminum brush housing is highly polished.
- Rubber Bumper: Extra wide, heavy duty, conductive rubber bumper around the brush housing
provides complete protection.
- Wheels: 5 inch diameter aluminum conductive wheels with bronze bushings. The entire
wheel carriage retracts to permit full weight of the machine on the brush
when the machine is in operation.
- Handle: Handle assembly is constructed of U.L. listed explosion proof fittings
and welded to prevent from loosening. The handle assembly is a fully adjustable
90 degrees for operator comfort and ease of storage. Two cord hooks provide
convenient storage for the trailing cord.
- Switch: Shock proof, double pole, momentary contact switch shuts off when the
switch lever is released.
- Cord: 50 foot, heavy duty reinforced U.L. listed 14/3 conductor cable. No plug is provided with the cord.
- Appearance: All cast aluminum parts are highly polished and all other exterior metal parts are chrome plated, except the handle fittings, which are aluminum painted.
Unico 15 inch floor buffer is certified for use with Class 1, Group D hazardous materials -
Atmospheres such as: acetone, acrylonitrile, ammonia, benzene, butane, 1-butanol,
2-butanol, n-butyl acetate, ethane, ethanol, ethyl acetate, ethylene dichloride,
gasoline, heptane, hexane, isoamyl alcohol, isoprene, methane, methanol, methyl
ethyl ketone, methyl isobutyl ketone, 2-methyl-1-propanol, naphtha, octane, pentane,
1-pentanol, propane, 1-propanol, 2-propanol, propylene, styrene, toluene, vinyl
acetate, vinyl chloride, and xylenes. |
|
| |
|
| |
| |
|
|
View Cart 
